Cementone Paveseal
Clear acrylic dustproofer and sealer

DESCRIPTION

Paveseal is a solvent-based clear acrylic penetrating sealer for application to bare brick, concrete, unglaze tiles and other masonry surfaces.

Treated surfaces exhibit reduced dusting and acts as a surface waterproofer against penetration by water, tills, grease etc. Paveseal is a low viscosity coating which results in good penetration into the substrate, and will enhances the colour of many surfaces giving a slightly darker and glossy tone to them. Paveseal is suitable for both interior and exterior use.

Note : Recurrence of efflorescence will not be totally prevented by application of a sealer.

TYPICAL PROPERTIES

  • Inhibits dust build up.
  • Enhances colour of treated substrate especially those with higher density.
  • Easily absorbed into the substrate and not just a coating on the surface.
  • Improve resistance to penetration by oil, grease
    and water.
  • Economical to use.
  • Easy to maintain and clean treated surface.
  • Suitable for both interior and exterior use.

SPECIFYING

"Cementone Paveseal" should be specified by name and used as per application procedures above.

Click Links Below For Our Products
Cementone Cemgrout GPA
Cementone Cemgrout NS
Cementone Prufe-it
Cementone Superplasticiser EB821-R
Marlease
Cementone No. 2
Cempatch -118
Cementone Paveseal
Mortar Clean
Superbond SBR
Powder Tile Adhesive
Expagate Standard
Cemplas
Conret
Expagate Spray
Superplastticiser EB 821-P
Cemcure EB 286 Clear
Cemcure EB 286 White
Cemcure EB 559 Clear
Cemcure EB 559 White
Conspeed
Cementone Hardflor-NOM Coloured
Cementone Hardflor-NOM
Cementone Hardflor-NM
Cementone Hardflor-NM Coloured

APPLICATION PROCEDURES

  • Surface Preparation
  1. The surface should be free of dirt, grease, oil, release-agents, silicon treatment and other contaminants.
  2. New concrete should be left for 28 days before application of Paveseal.
  3. Ensure that the working area is well ventilated to prevent excessive inhalation of the solvent during application and drying stages.
  • Application of Cementone Paveseal
  1. No primer is required.
  2. Apply 2 coats of Paveseal at a coverage of 5-8 m2 per litres per coat depending on the porosity of substrate.
  3. Allow an interval of 3 to 4 hours between coats.
  4. Allow 3 - 4 hours curing before suject to any foot traffic. Note : Avoid excessive quantities entering joints/sand grouting on paved areas.

PRODUCT DATA

Physical Appearance Clear low viscosity liquid.
Specific Gravity  0.88
Coverage 5 - 8 m2/litre per coat depending on porosity of substrate. Cure
Time 3 - 4 hours.
Flammable Flash point 47C
Packaging  5 titre or 25 litres container.
Storage Store in cool, dry place away from direct heat and sources of ignition.
Shelf Life 1 year in unopened original container.

CLEANING OF EQUIPMENT

  • Clean tools and others with aromatic solvents, e.g. Cellulose thinners.


Unicorp Sendirian Berhad Lot 66, Beribi II Industrial Estate,
B.S.B. BE1118 P.O. Box 620, Bandar Seri Begawan BS8671,
Brunei Darussalam
Tel: 673-245 0450, 245 0500, 245 0998
Fax: 673-245 0999 E-mail: unicorp@brunet.bn or unicorpbrunei@brunet.bn
Copyright Unicorp Sendirian Berhad All Rights Reserved 2005

pan> Flash point 47C Packaging  5 titre or 25 litres container. Storage Store in cool, dry place away from direct heat and sources of ignition. Shelf Life 1 year in unopened original container.

CLEANING OF EQUIPMENT


Unicorp Sendirian Berhad Lot 66, Beribi II Industrial Estate,
B.S.B. BE1118 P.O. Box 620, Bandar Seri Begawan BS8671,
Brunei Darussalam
Tel: 673-245 0450, 245 0500, 245 0998
Fax: 673-245 0999 E-mail: unicorp@brunet.bn or unicorpbrunei@brunet.bn
Copyright Unicorp Sendirian Berhad All Rights Reserved 2005